EN10111 DD1 steel for cold forming automobile us equivalent grades

The company regularly holds sales elites to share experiences, to promote the rapid growth of colleagues, and achieve the company and employees. The company conducts employee skill training and related knowledge video learning from time to time. All these

The company regularly holds sales elites to share experiences, to promote the rapid growth of colleagues, and achieve the company and employees. The company conducts employee skill training and related knowledge video learning from time to time. All these things is to improve the employees' skills and literacy, and reflects its own value. It has always been the pursuit of BBN steel to enhance the employee’s ability and keep up with the times.

The steel plate for water conservancy and power generation is used for ring seat, motor support structure, ship lock gate and discharge chute volute of large water conservancy generating units; the representative steel grades are S500Q, S550Q, SA516, etc., which require flaw detection and have Z-direction performance requirements; the main specifications are thickness of 120mm, 180mm, 200mm, 215mm, 270mm, and the maximum width is 4400mm. The representative steel grades of wind power steel plates include Q345E, Q690E, EN10111 DD1 steel for cold forming automobile, etc.; the main specifications are thickness of 80mm, 100mm, 110mm, 120mm, 140mm, 160mm, 180mm, 200mm, 240mm, 260mm, 280mm, 300mm, and the width is more than 2500mm.

The difference of chemical composition between EN10111 DD1 steel for cold forming automobile, Q420D steel and Q460D steel:
Chemical composition of Q420D steel: C ≤ 0.20, Si ≤ 0.50, Mn ≤ 1.70, P ≤ 0.030, S ≤ 0.025, Nb ≤ 0.07, V ≤ 0.20, Ti ≤ 0.20, Cr ≤ 0.30, Ni ≤ 0.80, Cu ≤ 0.30, N ≤ 0.015, Mo ≤ 0.20, Al ≥ 0.015. Chemical composition of Q460D steel: C ≤ 0.20, Si ≤ 0.60, Mn ≤ 1.80, P ≤ 0.030, S ≤ 0.025, Nb ≤ 0.11, V ≤ 0.20, Ti ≤ 0.20, Cr ≤ 0.30, Ni ≤ 0.80, Cu ≤ 0.55, N ≤ 0.015, Mo ≤ 0.20, B ≤ 0.004, Al ≥ 0.015.
The difference of mechanical properties between EN10111 DD1 steel for cold forming automobile, Q420D steel and Q460D steel:
The mechanical properties of Q420D steel: yield strength ≥ 420 MPa, tensile strength 500-680 MPa. The mechanical properties of Q460D steel: yield strength ≥ 460 MPa, tensile strength 500-720 MPa.

Main characteristics of 12Cr1MoV Steel: compared with 12CrMoV steel, 12Cr1MoV steel has higher oxidation resistance and thermal strength. The creep limit of 12Cr1MoV steel is very close to the endurance strength value, and it has high plasticity under the condition of endurance tension; the processability and weldability of 12Cr1MoV steel are good, but it needs to be preheated to 300 ℃ before welding, and stress removal treatment after welding. 12Cr1MoV steel is widely used in Superheater, header and main steam pipe of high pressure, ultra-high pressure and subcritical utility boiler.

The results of adopting two-level EN10111 DD1 steel for cold forming automobile service system and implementing standardized management are mainly reflected in the formation of vigorous work style such as quick response and quick action. Our company's customer service center stipulates that employees must be accurate and quick in technical support and EN10111 DD1 steel for cold forming automobile after-sales service. Through the formation of this fast, agile, vigorous style, to provide users with satisfactory service.

Our company has strict quality control standards. If you want to visit our factory, you are welcome at any time! We produce a lot of steel products every month to export EN10111 DD1 steel for cold forming automobile to all over the world. Because our customers are from all countries, they will order a large number of steel products from our company every month.